MAGNETEK GPD 515 PDF

The Yaskawa / Magnetek GPD /G5 Sine-Coded Pulse Width Modulated AC Motor Drive generates an adjustable voltage/frequency three phase output for. TTThhhooommmpppsssooonnn CCCooo RRReeellleeeaaassseeeddd /// /// 2. Magnetek GPD AC Drive Start Up and Adjustment Guide. Magnetek G5 GPD | Drives | NEW IN STOCK | CALL or Click for Quote.

Author: Zulkizil Daizahn
Country: Colombia
Language: English (Spanish)
Genre: Finance
Published (Last): 8 November 2017
Pages: 157
PDF File Size: 3.36 Mb
ePub File Size: 12.57 Mb
ISBN: 659-1-73552-607-7
Downloads: 7511
Price: Free* [*Free Regsitration Required]
Uploader: Shalrajas

A setting of ” 0. If auto-tuning is not possible, use section 2. A Outputs Analog Mahnetek Then DC injection current is applied. A I-2 Mode Selection A disconnect device can be installed for emergency stop purposes, but when that disconnect device is mxgnetek, there may be loss of electrical braking.

Learn More – opens in a new window or tab Any international shipping and import charges are paid in part to Pitney Bowes Inc.

Magnetek GPD Yaskawa AC Drive Control Gpdc-a 3phase | eBay

Encoder feedback option board types. Pressing this key will display the top level of the menu tree for returning to the Drive mode.

The measured resistance should be within the values listed in Table See Section 5 for description of hpd features, and also see instruction sheets for any options included with the drive.

Operation Selection at Speed Deviation Factory setting: Mid Frequency B o 1 – 0 5: Overall, very well done.

IMPORTANT. Engineering Bulletin #117 Magnetek GPD 515 Start Up and Adjustment Guide

Modify as necessary based on car speed and stopping distance. Multi-function Analog Monitor 1 Bias H 4 magnetrk 0 6: Write value to memory by pressing: Off-delay Timer Factory setting: Course content can be customized to the specific installation and application if requested. Apply power to the drive, but do N O T apply a run command.

  CORNING WCH-02P PDF

When drive output current is lower than the set value of b 3 – 0 2speed search is complete and acceleration or deceleration is continued at the normal rate C 1 – X X to set frequency.

Magnetek/Yaskawa GPD AC Drive Fault Indications

Trim Magnftek Level Factory setting: PumpSmart Commissioning Process 1. A E E E E 0. I found your company on line ,the sinumeric PCU50 was an obsolete part from the machine manufacturer so we where dead in the waterafter speaking to Joe he was very helpful and knowledgeable, he knew what we needed and the part was in stock newbut he also gave me some more economic options to choose fromi opted for the new unit and they shipped it the same day.

In this manual, safety messages are. We are not an authorized distributor or representative for pgd listed manufacturers.

The encoder then wires to the PG-X2 option board. See terms – opens in a new window or tab. This experience, combined with backgrounds in engineering and education, has earned national recognition for our technical training programs.

G;d setting depends on Control Method A PID Selection Factory setting: Elmont, New York, United States. The magnftek digit of the H 1 – 0 1 thru H 1 – 0 6 setting is entered in hexadecimal values which defines what type of external fault contact is used and how the drive will react to the fault input. CAUTION Applications that require decelerating large inertia loads in very short decel times may cause overshoots, and a possible runaway condition, causing equipment damage.

  ARCANOL MULTITOP PDF

Mount all optional power devices close to the drive, and keep electrical connections as short as possible. See Note 2 REF. Adjustment of zero-servo gain b may be required.

A given application requires that if motor speed were to ever reach RPM, an overspeed fault would occur and the motor should coast to stop. I will be shopping here again in the future should i have any need for more automation equipment like this again.

Any modification of the product by the user is not the responsibility of Yaskawa, and will void the warranty. Increases output frequency and voltage to compensate for motor slip.

Would recommend them to anyone. Run by frequency reference from control circuit terminal 13 or 14 and run command from control circuit terminal 1 or 2. When the run command is removed the drive decelerates to the designated dwell stop frequency b 6 – 0 3. Slip Compensation Gain Factory setting: